We introduce how to handle 2-way stainless steel bottles. Please take a look at the product you have and check the relevant parts.
Stainless Steel Bottle (15-4164-146）
Names of each part
Before using, please make sure that all parts are available.
How to attach and remove the shoulder strap
1. Insert the hook hole into the protrusion of the main body.
② Pull downward until it clicks and securely inserts.
[Heat and cold] Drinking cups (medium unit)
How to use
1) Remove the cup and the inside unit
Turn it in the direction of the arrow to remove it from the main unit.
② Put in your drink
Please keep the drinks in the position shown.
If you put it in too much, it can become hard to operate the inside lever or overflow with drinks, which can be dangerous.
POINT
Add a little hot water (cold water) and1Preheating (pre-cooling) for about minutes is effective in keeping the heat (cooling).
③ Close the middle unit
With the main unit upright, turn the inner unit in the direction of the arrow to tighten it.
*Please make sure there are no issues when the main unit is turned upside down.
! Note
When closing the inner unit, do not tilt or shake the unit.
④ Pour a drink
Push down the inner lever with your finger and tilt it towards the water inlet and pour it.
*Pouring with the water inlet facing downwards.
! Note
Do not push the inside lever down while tilting or swinging the unit.
It can cause the drink to leak, causing burns and dirt.
If the inner lever is too stiff to push, loosen the inner unit.
Then press down on the inside lever with your finger, and re-tighten the inside unit with the water inlet part open.
! Note
Do not drink directly through the water inlet.
For direct drinking, please use the lid unit.
⑤ When you finish drinking
1.When closing the inner lever, hold the main unit upright.2～3After a second has passed, press the inside lever (side the water inlet) to close.
! Note
Do not close the inside lever (water inlet side) while the main unit is tilted.
Drinks may remain around the water inlet or inside the inside of the water, and there is a risk of leakage.
2.Turn the cup in the direction of the arrow and close it firmly until it clicks.
! Note
Do not leave the inside lever open. It can cause a fall and spills the drink, causing burns and dirt.
How to remove and install the gasket
1. Push down the inner lever to make sure the bottom portion of the inner unit has dropped (opened), then remove and install the gasket.
② Check the up and down directions and install correctly. After installation, hold the gasket evenly with your fingers to prevent it from floating.
How to disassemble the medium unit
Push both knobs inward and pull up and remove the inside lid.
How to install the inner unit
Axially the water inlet of the inner lid and the inner lid, and press the inner lid firmly until you hear a click.
[For cold storage only] Direct drinking (lid unit)
How to use
1) Remove the lid unit
Turn it in the direction of the arrow to remove it from the main unit.
② Put in your drink
Please keep the drinks in the position shown.
Too much of it can cause drinks to overflow.
POINT
Put a small amount of cold water in the main unit,1Pre-cooling for about minutes is effective in keeping it cool.
③ Close the lid unit
With the main unit upright, turn the lid unit in the direction of the arrow.
※Please make sure the unit is upside down and there are no issues.
! Note
When closing the lid unit, do not tilt or shake the unit.
④ Drinking a drink
1. Raise the safety lock in the direction of the arrow to release it.
2. Press the button to open the hood.
3. Put your mouth on the mouth and tilt it slowly while drinking.
! Note
Do not open the hood while tilting or swinging the unit.
Even if the drink leaks, it can cause the food to get dirty.
⑤ When you finish drinking
1.With the main unit upright, close the hood firmly until it clicks.
2.Lower the safety lock in the direction of the arrow to ensure it is locked.
! Note
Do not leave the hood open.
It can cause a fall and spills your drink, causing it to become dirty.
*The hood cannot be tightened if the safety lock is lowered.
Make sure the safety lock is raised when closing the hood.
How to remove and install the gasket
① Food packing
When removing it, pinch the protruding part of the gasket with your finger to make it easier to remove.
When installing, push the recess of the gasket into the hood protrusion and hold it evenly with your fingers to prevent the gasket from floating. Install correctly so that the edges of the gasket do not get in.
② Lid packing
When removing it, pinch the guide part of the gasket with your finger to make it easier to remove.
When installing, check the up and down directions and install correctly. After installation, hold the gasket evenly with your fingers to prevent it from floating.
Handling precautions
- Do not leave it within reach of infants and young children. Also, be careful of children's pranks. It can cause burns and injuries, which can be dangerous.
- When using the product, a parent must be accompanied by a small child.
- Throw the shoulder strap over your shoulder, not around your neck. Also, do not play or exercise with the shoulder strap attached. There is a risk of choking or injury.
- When using the direct drinking unit (lid unit), it is only for cooling. Do not add hot drinks.
- Do not use for any purpose other than for adding drinks.
- Please be careful not to cover your face with product bags.
- Do not use a dishwasher or dish dryer.
- If you put in hot drinks, be careful not to roll over or burn. Also, do not let a hot kettle touch the opening.
- Do not bring it near fire on a stove or stove. This may cause burns, deformation or discoloration of the product.
- When using a cup (medium), especially if you put a hot drink in it, be sure to use the cup instead of drinking it directly. The drink comes out vigorously, causing burns.
- Do not swing or throw it around with your shoulder strap.
- Make sure that the gasket is installed correctly and that the inner and lid units are securely secured before using. This may cause leakage etc.
- Please keep the drinks in the position shown. If you put it in too much, it can be dangerous to overflow the drink. It may also cause burns and dirt during use.
- Never include the following:
- ① Dry ice/carbonated drink
- It is dangerous to increase the internal pressure, causing the medium-sized unit and lid unit to disappear or pop out, drinks may spout, or parts may break and scatter.
- ② Milk, milk drinks, fruit juice, etc. that are prone to decay
- ③ Miso soup, soup, etc. that contain a lot of salt
- The inner bottle is made of stainless steel, but there is a risk of rust.
- ④Tea leaves and flesh
- It can cause malfunctions such as clogging or leaking.
- When adding sports drinks, wash them immediately after use to prevent corrosion and rust. If there are scratches on the inside, do not put sports drinks in it.
- If you want to put large ice in, do not push it in and place it in small pieces. This can cause scratches and leaks.
- When closing the inner and lid unit, do not tilt or shake the main unit. This can cause drinks to overflow. It can also cause burns and burns and dirt.
- When cold drinks are placed or when the humidity is high, water droplets may be found on the inner and lid units.
- If you put something with a strong smell, the smell may transfer to the product, but this does not affect the quality.
- Do not carry the cup, inner unit or lid unit.
- When placing it in a bag, etc., make sure the unit is raised to prevent leakage.
- Do not put it in the freezer.
- Do not heat in the microwave.
- Do not drop or hit it to cause a strong impact. This may cause product deformation, cracking, and poor heat retention and cold retention.
- Do not leave the drink in for too long. It can cause decay and alteration.
- Do not leave your car in a medium or hot place.
- Please do not carry this product with precision equipment such as computers and cameras. If the drink leaks, it may cause damage or malfunction of the precision instrument.
- Do not use this product while driving or driving a car or bicycle as it is dangerous.
- Be sure to install special parts on the product.
- Never modify, disassemble or repair. It can cause malfunctions and accidents and is dangerous.
- Do not peel off the manufacturing lot stickers stuck on the bottom of the main unit.
Care instructions
- After use, be sure to wash it clean and dry thoroughly.
- To clean, soak a sponge or soft cloth in a neutral dishwash detergent, wash thoroughly with lukewarm water to prevent the detergent from rising, and dry thoroughly.
- If the dirt does not come off, please follow the [Care instructions for each part] below to use oxygen-based bleach (approximately 30 minutes).
- If you are not using it for a long time, wash it clean to remove any dirt, dry it thoroughly, and store it away from high temperatures and humidity.
[How to care for each part]
Cups, medium-sized units,
Lid unit
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
- Remove the cup, inner baking unit, and lid unit from the main unit, remove the gasket, then wash each unit cleanly and dry thoroughly. After cleaning, ensure that the gasket is installed in the correct position.
Cup, middle unit, lid unit
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
- Remove the cup, inner baking unit, and lid unit from the main unit, remove the gasket, then wash each unit cleanly and dry thoroughly. After cleaning, ensure that the gasket is installed in the correct position.
Inner bottle
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash clean with a bottle brush or sponge, remove any dirt, then rinse thoroughly with running water and allow to dry thoroughly. Although stainless steel is used, red spots like rust can form due to water quality and impurities. In such cases, add hot water with about 10% vinegar, and after about 30 minutes, wash the inside with a soft brush and rinse thoroughly.
- *If using oxygen-based bleach, do not install the medium-sized unit or lid unit. It is dangerous, such as the internal pressure of the main unit increasing and the inner pressure unit and lid unit being damaged or scattered.
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash clean with a bottle brush or sponge, remove any dirt, then rinse thoroughly with running water and allow to dry thoroughly. Although stainless steel is used, red spots like rust can form due to water quality and impurities. In such cases, add hot water with about 10% males, and after about 30 minutes, wash the inside with a soft brush and rinse thoroughly.
- *If using oxygen-based bleach, do not install the shingle unit. It is dangerous, such as the internal pressure of the main unit being increased and the inner pressure unit may be damaged or scattered.
Outside of the main body (shoulder, body, bottom)
- How to wash
- ⚪︎ Washing with running water
- × Soaking
- × Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash thoroughly, drain well, immediately wipe off the moisture with a dry cloth and allow it to dry thoroughly.
-
*Please do not soak the whole unit in soak. This can cause poor heat and cold retention. (Inner bottles can be washed in soaking)
- How to wash
- ⚪︎ Washing with running water
- × Soaking
- × Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash thoroughly, drain well, immediately wipe off the moisture with a dry cloth and allow it to dry thoroughly.
-
*Please do not soak the whole unit in soak. This can cause poor heat and cold retention. (Inner bottles can be washed in soaking)
Care precautions
- Do not boil. The heat can deform the product and cause damage such as leakage.
- Do not use a dishwasher or dish dryer.
- Do not leave the main unit in water. This can cause rust, poor heat retention and cold retention.
- Do not use chlorine bleach, thinners, benzine, metal scrubbers, brush powders, or cleansers.
- Do not use bleach on the outside of the unit. This can cause peeling of paint, printing, stickers, etc.
Q&A
What if the drink gets leaked?
- Make sure the gasket is installed correctly and the inner and lid units are securely fastened.
- Make sure you have not added too much drinks.
- Please check that the inner cavity unit, lid unit, and gasket are not damaged or worn.
What if the bottle inside the main unit discolors?
- If there is dirt on it, wash it thoroughly with a sponge with dishwashing detergent. If the dirt on the inside of the unit does not come off, use oxygen bleach (approximately 30 minutes).
- !Note
- Please read the precautions for oxygen bleach carefully and use correctly.
What if the heat and cold retention effect is not effective?
- Make sure you have a hot (cold) drink in it. It is effective to pour a small amount of boiling water (cold water) into the main unit and preheat (pre-cool) for about a minute.
- If you have little drinks or ice, increasing the amount is effective.
- Please check that the unit is not damaged. Fill in almost a full amount of boiling water, and after 20 to 30 minutes, if it feels warm to touch the body with your hand, consult the store where you purchased it.
What if it smells strange?
- Please check that there is no dirt on the inner bottle, inner unit, and lid unit.
What if the gasket has discolored?
- If there is dirt or mold attached, follow the care instructions to use oxygen bleach.
- If dirt or mold does not come off, buy a new gasket.
Thermal and cold retention properties
| Thermal effect | (When using the inner casing (with cup)) 72 degrees or higher (6 hours) |
|---|---|
| Cold retention effect | (When using the inner casing (with cup)) 10 degrees or less (6 hours) (When using the lid unit) 10 degrees or less (6 hours) |
*The cold retention effect is the temperature at room temperature of 20°C ± 2°C, when the product is filled with cold water to the bottom edge of the inner and lid unit, and placed vertically, and left for 6 hours with the inner and cups and lid units attached.
Raw materials and materials used
| Part Name | Raw material resin | Materials used | |
|---|---|---|---|
| Inner bottle | stainless steel | ||
| Shoulder | polypropylene | ||
| Torso | stainless steel (Acrylic resin coating) |
||
| Bottom | polypropylene | ||
| Inner (with cup) | The inside body | polypropylene | |
| Interior lid | polypropylene | ||
| Interior lever | ABS resin | ||
| Middle gasket | Silicone rubber | ||
| Cup | polypropylene | ||
| Lid unit | lid | polypropylene | |
| Food | polypropylene | ||
| Drinking tip | polypropylene | ||
| Food packing | Silicone rubber | ||
| Lid packing | Silicone rubber | ||