MIKI HOUSEWe introduce how to handle Bear stainless steel bottles. Please take a look at the product you have and check the relevant parts.
Stainless Steel Bottle (15-4163-686）
Names of each part
Before using, please make sure that all parts are available.
How to remove the gasket
Take care not to damage the gasket.
How to install the gasket
Check the up and down directions and install correctly.
After installing, hold the gasket evenly with your fingers to make sure the gasket is not floating.
How to use
1) Remove the sen unit and drinking unit
Turn the sen and drinking units in the direction of the arrow to remove them.
② Put in your drink
Please keep the drinks in the position shown.
If you put it in too much, it can cause drinks to overflow when you close the unit.
POINT
Put a small amount of boiling water (cold water) into the main unit and preheat (pre-cool) for about a minute, making it effective in keeping the body warm (cold).
③ Close the drinking unit and the stove unit
With the main unit upright, turn the drinking unit and slurp unit in the direction of the arrow to ensure close.
*Please make sure that the main unit is turned upside down.
Note
When tightening the drinking unit or caulking unit, do not tilt or shake the unit.
Drinks may spill, causing burns and dirt.
④ Drinking a drink
1) With the main unit upright, hold the main unit and turn the unit in the direction of the arrow to open it.
Note
If you turn the unit while tilting or shaking the unit, the drink may spill, causing burns and dirt to occur.
2) Put your mouth on the mouth and tilt it slowly while drinking.
Note
If you drink hot drinks, be careful of burns.
⑤ When you finish drinking
With the main unit upright, rotate the unit in the direction of the arrow until it no longer rotates to tighten it firmly.
Note
- Make sure the unit is securely stored.
- Do not leave the unit open. It can cause a fall and spills the drink, causing burns and dirt.
Handling precautions
Do not leave it within reach of infants and young children. Also, be careful of children's pranks. It can cause burns and injuries, which can be dangerous.
- Do not use for any purpose other than for adding drinks.
- Please be careful not to cover your face with product bags.
- Do not use a dishwasher or dish dryer.
- If you put in hot drinks, be careful not to roll over or burn. Also, do not let a hot kettle touch the opening.
- Do not bring it near fire on a stove or stove. This may cause burns, deformation or discoloration of the product.
- Make sure that the gasket is installed correctly and that the baking unit and drinking unit are securely securely stored before using. This may cause leakage etc.
- Do not shake the unit immediately after adding a hot drink. The internal pressure may rise suddenly, making it difficult for the slurping unit to open, or a sound may occur when it is opened.
- If you put a hot drink in it and leave it for a long time, the internal pressure may decrease, making it difficult for the slurping unit to open, or you may hear a sound when it opens.
- When putting your mouth on the mouth, do not tilt it suddenly. The drink comes out vigorously, causing burns and other symptoms.
- Please keep the drinks in the position shown. If you put it in too much, the drink will overflow when you close the unit, or it will leak during use, causing burns and dirt.
- Never include the following:
- ① Dry ice/carbonated drink
- It is dangerous that the internal pressure may increase, causing the slurping unit to disappear, drinks may slurp, or the slurp unit may break and scatter.
- ② Milk, milk drinks, fruit juice, etc. that are prone to decay
- ③ Miso soup, soup, etc. that contain a lot of salt
- The inner bottle is made of stainless steel, but there is a risk of rust.
- ④Tea leaves and flesh
- It can cause malfunctions such as clogging or leaking.
- When adding sports drinks, wash them immediately after use to prevent corrosion and rust. If there are scratches on the inside, do not put sports drinks in it.
- If you want to put large ice in, do not push it in and place it in small pieces. This can cause scratches and leaks.
- When tightening the unit, do not tilt or shake the unit. This can cause drinks to overflow. It can also cause burns and burns and dirt.
- When cold drinks are placed in or when the humidity is high, water droplets may be found on the slurp or drinking unit.
- If you put something with a strong smell, the smell may transfer to the product, but this does not affect the quality.
- Do not carry the unit with you.
- When putting it in a bag, etc., make sure to stand with the unit facing up to prevent leakage.
- Do not put it in the fridge.
- Do not heat in the microwave.
- Do not drop or hit it to cause a strong impact. This may cause product deformation, cracking, and poor heat retention and cold retention.
- Do not leave the drink in for too long. It can cause decay and alteration.
- Do not leave your car in a medium or hot place.
- Please do not carry this product with precision equipment such as computers and cameras. If the drink leaks, it may cause damage or breakdown of the precision instrument.
- Do not use this product while driving or driving a car or bicycle as it is dangerous.
- Never modify, disassemble or repair. It can cause malfunctions and accidents and is dangerous.
- Do not peel off the manufacturing lot stickers stuck on the bottom of the main unit.
Care instructions
- After use, be sure to wash it clean and dry thoroughly.
- To clean, soak a sponge or soft cloth in a neutral dishwash detergent, wash thoroughly with lukewarm water to prevent the detergent from rising, and dry thoroughly.
- If the dirt does not come off, please follow the [Care instructions for each part] below to use oxygen-based bleach (approximately 30 minutes).
- If you are not using it for a long time, wash it clean to remove any dirt, dry it thoroughly, and store it away from high temperatures and humidity.
[How to care for each part]
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
- Remove the slurping unit and drinking unit from the main unit, remove the slurping and drinking mouth gasket, then wash each unit cleanly and dry thoroughly. After cleaning, ensure that the gasket and mouthpiece gasket are installed in the correct position.
[How to care for each part]
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
- Remove the slurping unit and drinking unit from the main unit, remove the slurping and drinking mouth gasket, then wash each unit cleanly and dry thoroughly. After cleaning, ensure that the gasket and mouthpiece gasket are installed in the correct position.
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash clean with a bottle brush or sponge, remove any dirt, then rinse thoroughly with running water and allow to dry thoroughly. Although stainless steel is used, red spots like rust can form due to water quality and impurities. In such cases, add hot water with about 10% vinegar, and after about 30 minutes, wash the inside with a soft brush and rinse thoroughly.
- *If using oxygen-based bleach, do not install the shingle unit. It is dangerous to increase the internal pressure of the main unit and cause the unit to break or scatter.
- How to wash
- ⚪︎ Washing with running water
- ⚪Soaking and wash
- ⚪Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash clean with a bottle brush or sponge, remove any dirt, then rinse thoroughly with running water and allow to dry thoroughly. Although stainless steel is used, red spots like rust can form due to water quality and impurities. In such cases, add hot water with about 10% vinegar, and after about 30 minutes, wash the inside with a soft brush and rinse thoroughly.
- *If using oxygen-based bleach, do not install the shingle unit. It is dangerous to increase the internal pressure of the main unit and cause the unit to break or scatter.
- How to wash
- ⚪︎ Washing with running water
- × Soaking
- × Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash thoroughly, drain well, immediately wipe off the moisture with a dry cloth and allow it to dry thoroughly.
-
*Please do not soak the whole unit in soak. This can cause poor heat and cold retention. (Inner bottles can be washed in soaking)
- How to wash
- ⚪︎ Washing with running water
- × Soaking
- × Oxygen bleach
- × Chlorine bleach
- Care instructions
-
Wash thoroughly, drain well, immediately wipe off the moisture with a dry cloth and allow it to dry thoroughly.
-
*Please do not soak the whole unit in soak. This can cause poor heat and cold retention. (Inner bottles can be washed in soaking)
Care precautions
- Do not boil. The heat can deform the product and cause damage such as leakage.
- Do not use a dishwasher or dish dryer.
- Do not leave the main unit in water. This can cause rust, poor heat retention and cold retention.
- Do not use chlorine bleach, thinners, benzine, metal scrubbers, brush powders, or cleansers.
- Do not use bleach on the outside of the unit. This can cause peeling of paint, printing, stickers, etc.
Q&A
What if the drink gets leaked?
- Make sure that the drinking unit is installed correctly and that the drinking unit and drinking unit are securely clamped.
- Make sure you have not added too much drinks.
- Make sure the gasket is securely attached.
- Please check that the sen and drinking units are not damaged or worn out.
What if the bottle inside the main unit discolors?
- If there is dirt on it, wash it thoroughly with a sponge with dishwashing detergent. If the dirt on the inside of the unit does not come off, use oxygen bleach (approximately 30 minutes).
- Note
- Please read the precautions for oxygen bleach carefully and use correctly.
What if the heat and cold retention effect is not effective?
- Make sure you have a hot (cold) drink in it. It is effective to pour a small amount of boiling water (cold water) into the main unit and preheat (pre-cool) for about a minute.
- If you have low drinks or ice, increasing the amount of drinks is effective.
- Please check that the unit is not damaged. Fill in almost a full amount of boiling water, and after 20 to 30 minutes, if it feels warm to touch the body with your hand, consult the store where you are purchasing it.
What if it smells strange?
- Please check that there is no dirt on the bottle and drinking unit inside the main unit.
What if the gasket has discolored?
- If there is dirt or mold attached, follow the care instructions to use oxygen bleach.
- If dirt or mold does not come off, buy a new gasket.
About purchasing parts
- If you would like to purchase parts,HerePlease contact us from.
Thermal and cold retention properties
| Thermal effect | 88 degrees or higher (1 hour) / 73 degrees or higher (6 hours) |
|---|---|
| Cold retention effect | 9 degrees or less (6 hours) |
Raw materials and materials used
| Part Name | Raw material resin | Materials used |
|---|---|---|
| Inner bottle | stainless steel | |
| Shoulder | stainless steel | |
| Torso | stainless steel (Acrylic resin coating) |
|
| plug | polypropylene (Built-in Styrofoam) |
|
| Drinking tip | polypropylene | |
| Sensor packing | Silicone rubber | |
| Drinking mouth packing | Silicone rubber |